User Manual

Profiling Projects – An Introduction

Updated on

In this article, you will learn

  • what a profiling project is,
  • why profiling a printing system is necessary, and
  • which advantages the project-based approach offers.

1. Introduction

Digital printing systems do not behave linearly in their color reproduction. Doubling the printed tonal value does not double the perceived color density and the relationship between the controlled value and their printed result differs from channel to channel. The following factors influence this behavior:

  • Substrate – absorption behavior, surface and paper white of substrates as well as optical brighteners change color results considerably.
  • Ink quantity – when a certain total area coverage is being exceeded, color effects no longer increase but drying problems and substrate deformation arise.
  • Extended color gamuts – extended gamut colors and light inks must be integrated into the separation to be usable at all.
  • Additional fluids – white, primer or varnish influence color results if printed. They must be taken into account during profiling.
  • Condition of the printing system – print heads, ink batches and ambient conditions change over time.

Without profiling, color results are not predictable or repeatable. They cannot be checked against a reference color space. Customer approval, compliance with standards and reproducible reprints are only possible once the behavior of the printer/substrate combination has been measured and stored.

For $PRODUCT_NAME_WORKFLOW to control a printing system with color accuracy, these color reproduction properties must be determined once and stored in the system. The project in which these properties are captured, measured and evaluated is referred to as a profiling project.

2. Profiling Projects in Detail

Profiling a printing system consists of several steps that build on each other. Each of these steps requires the same basic conditions: the same printing system, the same print configuration, the same reference substrate, the same measurement device and the same parameter set. If these basic conditions are defined separately for each step, deviations occur that can no longer be traced in the result.

For this reason, $PRODUCT_NAME_WORKFLOW combines all steps of profiling in one project. The concept is based on the following considerations:

  • Reference combination as the starting point – a profiling project is created for exactly one printer, one print configuration (resolution), one maximum color configuration and one reference substrate. The print configuration selected is the one that usually delivers the best possible print quality and the substrate selected is the one that ensures the largest possible color gamut. All other combinations are derived from this reference profiling.
  • Defined once instead of entered repeatedly – information such as the measurement device, the parameter set and additional fluids are stored when the profiling project is created and applied in the individual steps. This ensures that steps of the same project cannot be created under different conditions.
  • Traceable dependencies – settings that significantly determine the result but lie outside the project are documented in the project itself. This applies in particular to the CMYK and RGB working color spaces, which are used as the basis for calculating the substrate DeviceLink profiles.
  • Guided process with graduated level of detail – in Standard Mode, you are only asked for what is mandatory to create a profiling project and which substeps are necessary in the individual steps of the profiling project. Expert Mode provides further options for intervention in greater detail.
  • Derivation from the master data and templates – whether a step is required at all depends on the selected printing system. Steps that are not needed for the selected printing system are not offered. If a step must be completed, templates are available that you can select, so that in-depth expert knowledge is not required.
  • Saving the measurement data – measurements are saved in the respective step and retained. This allows you to repeat measurements and compare results without having to set up the project again.

2.1. Structure of a Profiling Project

A profiling project is divided into steps that are completed in a fixed order. Depending on the selected printing system and the selected options, the following steps are available:

The same substeps are repeated within these steps. A measurement template chart is printed, the printed chart is measured, the measurement data is analyzed and a profile (usually a DeviceLink profile) is created based on the measurement data.

2.2. Advantages of a Profiling Project

Compared to a sequence of individual profiling steps, the project-based approach offers the following advantages:

  • Completeness – the order of the steps and the results required for the next step are predefined. This makes it possible to identify a printing system that has not been fully profiled.
  • Consistency – all steps of a project are based on the same basic conditions. Deviations caused by different measurement devices, parameter sets or working color spaces within one profiling are avoided as far as possible – in some exceptional cases, practical solutions must be offered.
  • Traceability – measured data and the settings used are retained in the project and can still be checked months later.
  • Multiple use – several Color Policies can be derived from a completed reference profiling, for example for different separation settings, further color configurations, substrates with different properties and matching profiles for other printing systems.
  • Maintenance instead of re-profiling – if the condition of the printing system changes, it is first corrected using Re-Characterization. A complete re-profiling is only required when several iterations of corrections are no longer sufficient.
  • Reduced training effort – Standard Mode guides you through the necessary steps, while Expert Mode provides the color management expert with the additional options that are needed for different requirements.

2.3. Result of a Profiling Project

A completed profiling project provides the Color Policies that are needed to output production jobs. A profiling project can contain the following information:

  • a Color Policy that describes the color gamut of the reference combination of printer, print configuration, color configuration, selected substrate, the total area coverage limit to be applied and the linearization with its transitions
  • several Color Policies with different separation settings and modified transitions
  • several Color Policies for different color configurations within one printing system or across several printing systems
  • several Color Policies for substrates with different substrate properties
  • several Color Policies with matching profiles for other printing systems

Further information on Profiling Projects

For more information on managing profiling projects and their user interface, see Conception and User Interface. How to create a profiling project and which setting options are available, please see Creating a Profiling Project.

3. Standard Mode vs. Expert Mode

Profiling a printing system involves a large number of settings – most of them are only needed for special cases and require colorimetric knowledge. For this reason, two operation levels are offered: Standard Mode and Expert Mode.

Both modes access the same range of background functions. The difference lies in the number of settings shown in the dialog and in which calculated values can be changed.

You switch modes directly in the open dialog using the Expert Mode option. This does not switch a single dialog, but your operating mode. If Expert Mode is enabled, the extended setting options are available in all dialogs in which they are offered.

3.1. Standard Mode

Standard Mode is the default mode. It covers all settings that are required to create a profiling project and complete all its steps. Therefore, a profiling project carried out in Standard Mode is complete and ready for production.

Standard Mode is characterized by the following features:

  • Predefined values – information such as color configuration, working color spaces or tolerances is taken from the master data and the system settings and is not offered for selection. The color configuration used is the one that includes all process colors of the inks available in the printer.
  • Calculated values are applied – calculated values and curves are applied. Changing these values is not intended in Standard Mode.
  • Reduced views – the calculated results are displayed. Additional charts and evaluations remain hidden.
  • Predefined process – which steps are completed in the profiling project depends on the selected printing system and the master data.

3.2. Expert Mode

Expert Mode is intended for users who need greater control over the profiling and the profile calculation. Enabling Expert Mode shows additional setting options, additional tabs and additional views. These include the following options, among others:

  • Different basic conditions – you can choose color configurations, CMYK working color spaces and RGB working color spaces. They are used as a foundation to calculate substrate DeviceLink profiles.
  • Control of the steps – additional setting options like Pre-Linearization, Linearization, and G7-Linearization are available if needed.
  • Intervention in the calculation – you can change calculated values and curves, for example as part of the ink cut.
  • Extended evaluation – additional views, such as the curves based on the measurement data, are shown.
  • Assignment of the Color Policies – you can assign the Color Policies created in the project to all substrates or an extended selection of substrates.

As the name suggests, Expert Mode is intended for color management experts. One example is a profiling project for a specific color configuration that lies well outside the normal production conditions for a specific substrate.

Artikel Update: $PRODUCT_NAME_WORKFLOW 2.4 – 11/2026

Next Article Conception and User Interface